All Plumbing Repairs and Services

Mon-Sat: 07:00 - 17:00

24h Emergency Service

Get Warranty

Register Your Warranty

Call Today 222 468 532

Manhattan, NY 10039

Common Plumbing Problems and How to Fix Them

As a homeowner, encountering plumbing problems is almost inevitable. While some issues require the expertise of a professional plumber, many common plumbing problems can be resolved with a bit of know-how and the right tools. This blog will cover some of the most frequent plumbing problems and provide practical solutions to fix them.

1. Dripping Faucets

Problem:

A dripping faucet is not only annoying but can also waste a significant amount of water over time, leading to increased water bills.

Cause:

The most common cause of a dripping faucet is a worn-out washer. When the washer deteriorates, it no longer creates a watertight seal, allowing water to escape.

Solution:

  1. Turn Off the Water Supply: Before starting, ensure the water supply to the faucet is turned off.
  2. Disassemble the Faucet: Use a wrench to remove the handle and access the internal parts.
  3. Replace the Washer: Identify the worn-out washer and replace it with a new one of the same size.
  4. Reassemble the Faucet: Put the faucet back together and turn on the water supply to check if the dripping has stopped.

2. Slow or Clogged Drains

Problem:

Slow or clogged drains can cause water to back up in sinks, showers, and tubs, creating an unpleasant mess and potential water damage.

Cause:

Clogs are typically caused by a buildup of hair, soap scum, food particles, and other debris in the drain pipes.

Solution:

  1. Boiling Water: Pouring boiling water down the drain can help dissolve soap scum and grease clogs.
  2. Plunger: Use a plunger to create suction and dislodge the clog. Ensure there’s enough water to cover the plunger’s rubber part for better suction.
  3. Drain Snake: A drain snake or auger can reach further into the pipes to break up stubborn clogs.
  4. Baking Soda and Vinegar: Pour a mixture of baking soda and vinegar down the drain. After the fizzing subsides, flush with hot water.

3. Running Toilets

Problem:

A running toilet can waste hundreds of gallons of water daily, significantly impacting your water bill.

Cause:

The most common causes are a faulty flapper valve, a float that’s not correctly balanced, or a fill tube that’s too long or short.

Solution:

  1. Check the Flapper Valve: Inspect the flapper valve at the bottom of the tank. If it’s not sealing properly, replace it.
  2. Adjust the Float: Ensure the float is at the correct level. If it’s too high or too low, adjust it to the manufacturer’s recommended level.
  3. Shorten or Lengthen the Fill Tube: Ensure the fill tube is the proper length to prevent water from continuously filling the tank.

4. Low Water Pressure

Problem:

Low water pressure can make simple tasks like showering or washing dishes frustratingly slow.

Cause:

Low water pressure is often due to sediment buildup in pipes, a malfunctioning pressure regulator, or leaks.

Solution:

  1. Clean Aerators and Showerheads: Mineral deposits can clog aerators and showerheads. Remove them and soak in vinegar overnight, then scrub off the deposits.
  2. Check for Leaks: Inspect visible pipes and fixtures for leaks that might reduce water pressure.
  3. Pressure Regulator: If you have a pressure regulator, ensure it’s functioning correctly. You may need to adjust or replace it if it’s faulty.

5. Leaky Pipes

Problem:

Leaky pipes can cause water damage, mold growth, and increased water bills.

Cause:

Leaks often occur due to corrosion, high water pressure, or damaged pipe joints.

Solution:

  1. Temporary Fixes: Use pipe clamps or epoxy putty for a temporary fix until a professional can make a permanent repair.
  2. Replace Damaged Sections: If you’re comfortable with DIY plumbing, replace the damaged section of the pipe using couplings and the appropriate type of pipe.
  3. Reduce Water Pressure: High water pressure can cause leaks. Ensure your home’s water pressure is within the recommended range.

6. Water Heater Issues

Problem:

A malfunctioning water heater can result in no hot water, inconsistent temperatures, or strange noises.

Cause:

Common issues include sediment buildup, faulty thermostats, or heating elements.

Solution:

  1. Flush the Tank: Sediment buildup can cause problems. Drain and flush the water heater tank to remove sediment.
  2. Check the Thermostat: Ensure the thermostat is set to the correct temperature and functioning correctly.
  3. Inspect Heating Elements: If you’re comfortable with electrical work, check the heating elements for continuity and replace them if necessary.

7. Garbage Disposal Jams

Problem:

A jammed garbage disposal can cause a sink backup and unpleasant odors.

Cause:

Disposals can jam due to bones, fibrous vegetables, or other inappropriate items being placed in them.

Solution:

  1. Turn Off the Power: Always ensure the power is off before working on the disposal.
  2. Manual Rotation: Use a hex wrench to manually rotate the disposal motor from underneath the unit to clear the jam.
  3. Reset Button: Press the reset button on the bottom of the disposal unit to restart it.

Conclusion

While many common plumbing problems can be fixed with a bit of DIY effort, it’s essential to recognize when a problem is beyond your capabilities and requires professional help. Regular maintenance and timely repairs can prevent minor issues from turning into major headaches. If you’re ever in doubt, don’t hesitate to call a professional plumber to ensure your home’s plumbing system remains in top shape.

Leave a Reply

Your email address will not be published. Required fields are marked *

Recent Comments
    About

    Professional Plumbers Denver, offers a variety of services to meet your construction needs, from a simple plumbing fixture repair or replace to a residential / Commercial plumbing system install. We believer every project should be treated as we are doing it for our family. Your satisfaction is our long term goal.

    X