Professional Backflow Prevention Services in Denver
Licensed Denver plumbers for backflow preventer installation, repair and replacement, with clear guidance on Denver Water testing requirements for homes, businesses and irrigation systems.
Enter your contact details here
Call (720) 390-2652 | Request Backflow Prevention Service
Your drinking water is only as safe as the connections around it. A backflow prevention assembly is the device that keeps used or contaminated water from flowing backward into clean water lines. Professional Plumbers Denver installs, repairs and replaces backflow preventers for homes, businesses and irrigation systems in Denver and nearby communities.
Rules for backflow assemblies depend on your water provider and your property’s hazard level, so we start by understanding your property and your device, then explain what is needed. If you have received a letter or test notice, have it ready when you call.
What Is Backflow Prevention and Why Does It Matter?
Backflow is water flowing in the opposite direction from normal. It happens two ways. Backsiphonage occurs when supply pressure drops, for example during a water main break or heavy firefighting demand, and water is pulled backward. Backpressure occurs when pressure on the property side is higher than the supply, which can happen with boilers, pumps and elevated tanks.
Backflow becomes dangerous at a cross-connection, any link between the drinking water supply and a possible source of contamination, such as an irrigation system treated with fertilizer, a boiler loop or a hose placed in a pool. A backflow prevention assembly blocks reverse flow at that connection and protects both your water and the public water supply.
Our Backflow Prevention Services
Backflow Preventer Installation
We install backflow assemblies on domestic water lines, irrigation systems and commercial services, choosing the assembly type that fits the property and its hazard level. Location matters: assemblies need the right height, clearance for testing and protection from freezing. Denver Water requires approved assemblies, and a new assembly must be tested after installation. See the compliance section below.
Backflow Assembly Testing: What It Involves
A backflow test uses calibrated gauges to confirm that the check valves hold, the relief valve opens when it should and the shutoff valves seal. Denver Water requires testing when an assembly is installed and every year after that, performed by a certified backflow prevention assembly tester, with the report sent to Denver Water. Call (720) 390-2652 and tell us about your assembly, and we will explain how we can help with testing for your property.
Backflow Preventer Repair
Common repairs include replacing fouled or worn check valves, seals, springs and relief valve parts, and fixing leaking test cocks or damaged shutoff valves. After a repair, the assembly has to be tested again and the passing report submitted to the water provider.
Backflow Device Replacement
When an assembly is corroded, damaged by freezing, obsolete or failing repeatedly, replacement is often the better value. We replace it with an approved assembly suited to the property’s hazard level and make sure the new device is installed so it can be tested and serviced.
Irrigation Backflow Prevention
Irrigation systems are a common cross-connection because they connect to drinking water and may carry fertilizer or soil contaminants. Denver Water requires irrigation assemblies to be tested by a certified tester as the water is turned on for the season. For irrigation devices, startup and winterization, see our vacuum breaker and backflow preventer service, sprinkler line repair and winterization.
Commercial Backflow Prevention
Denver Water requires an approved backflow prevention assembly on commercial, industrial and fire line services. Restaurants, offices, apartment buildings, boilers and other systems can pose higher hazards that call for stronger assemblies such as RPZs. We install, repair and replace commercial assemblies. For the wider picture, see our commercial plumbers in Denver.
Questions about your device or a notice you received? Call (720) 390-2652.
Types of Backflow Prevention Devices
The right assembly depends on the hazard level of the connection, the water provider’s rules and how the system is laid out. Always confirm the required type before you buy.
Reduced Pressure Zone (RPZ) Assemblies
An RPZ has two check valves with a relief valve between them. If either check valve fails or pressure changes, the relief valve opens and discharges water. RPZs give the highest level of protection and are used where the hazard is higher, as on many commercial and industrial connections.
Double Check Valve Assemblies
A double check valve assembly (DCVA) has two check valves in series and no relief valve. It is used for lower-hazard connections and is common on some fire lines and low-hazard commercial services.
Pressure Vacuum Breakers
A pressure vacuum breaker (PVB) combines a check valve with an air inlet. It is commonly used on irrigation systems, and it must be installed above the highest downstream outlet so it can work as designed.
Common Backflow Prevention Problems
| Problem | Possible cause | Next step |
|---|---|---|
| Water dripping or discharging from an RPZ relief valve | Fouled or worn check valve, debris, pressure fluctuations | Have the assembly inspected and repaired; discharge usually signals a problem |
| Failed backflow test | Worn seals or springs, debris, damaged check valves | Repair or replace parts, then retest and submit the passing report |
| Leaking test cock or shutoff valve | Worn seals or corrosion | Repair or replace the leaking part |
| Corrosion or rust on the assembly | Age, moisture, harsh conditions | Inspect; replace if the body is damaged |
| Reduced water pressure | Debris in the assembly, partly closed valves, undersized device | Have a plumber inspect the assembly and the supply line |
| Freeze or weather damage | Exposed assembly in cold weather | Inspect after thaw; repair or replace; see our frozen pipe repair page |
| Improper installation | Wrong orientation, height or clearance, or the wrong assembly type | Have it corrected and retested |
| Annual test notice | Your water provider’s yearly requirement | Hire a certified tester and send in the report before the deadline |
Denver Backflow Testing and Compliance Requirements
This summary comes from Denver Water’s Cross-Connection Control and Backflow Prevention Program page, reviewed in November 2026. Rules can change, so check Denver Water’s program page for the current version.
- Who needs an assembly: commercial, industrial, irrigation and fire line services must have an approved backflow prevention assembly. Customers with an auxiliary water supply such as a well or pond must also install and maintain one. Requirements for single-family and multi-family residences are assessed based on site hazards, so not every home needs a device.
- Testing: the assembly must be tested when it is installed and annually after that by a certified backflow prevention assembly tester. Denver Water’s guidance names testers certified by ABPA or ASSE.
- Reporting: test results must be reported to Denver Water’s Cross-Connection Control office on its test report form.
- Irrigation: irrigation assemblies are tested as the water is turned on for the season.
- State rules: the program follows the Colorado Primary Drinking Water Regulations (Regulation 11), overseen by the Colorado Department of Public Health and Environment.
Denver Water serves much of Denver but not every nearby community. If your water comes from another provider, such as the city or a local district, its rules may differ. Check your water bill or ask us.
A plumber’s license and a backflow tester certification are two different credentials. Ask any tester for their certification number before the test.
Residential and Commercial Backflow Prevention
Residential: homes with irrigation systems, wells, ponds or other cross-connections may need protection, and Denver Water assesses residences based on site hazards. If you are not sure whether your home needs an assembly, check with Denver Water or call us.
Commercial: businesses often need larger or higher-protection assemblies and have more fixtures and equipment that can create cross-connections. We install, repair and replace commercial assemblies and can talk through what your property needs.
Why Choose Professional Plumbers Denver
- Licensed and insured plumbers for residential and commercial properties.
- Open 24/7 for plumbing emergencies, including leaking or damaged assemblies.
- Free on-site assessment and upfront pricing, so you know the cost before work starts.
- Serving Denver since 2005.
- Clear explanations of what your assembly needs and what your water provider requires.
- Local Denver office at 4400 S Quebec St, Suite 208, Denver, CO 80237.
Backflow Prevention FAQs
A backflow prevention device, also called an assembly, is a mechanical device that stops water from flowing backward into the clean drinking water supply. It uses check valves, and in some designs a relief valve or air inlet, to block reverse flow caused by pressure changes.
Backflow can pull contaminants such as fertilizer, chemicals or bacteria from a building or irrigation system into the drinking water. Backflow assemblies protect your own water and the public water supply, which is why water utilities such as Denver Water run cross-connection control programs.
Denver Water requires an assembly to be tested when it is installed and every year after that by a certified backflow prevention assembly tester, with the test report sent to Denver Water. Irrigation assemblies are tested as the water is turned on for the season. Check Denver Water's program page for current details.
Denver Water requires an approved assembly on commercial, industrial, irrigation and fire line services, and on any service with an auxiliary water supply such as a well or pond. Requirements for single-family and multi-family homes are assessed based on site hazards, so not every home needs one. If you are unsure, contact Denver Water or call us.
A reduced pressure zone (RPZ) assembly has two check valves with a relief valve between them that discharges water if either check valve fails or pressure changes. It provides the highest level of protection and is used where the hazard is higher, such as many commercial and industrial connections.
A double check valve assembly has two check valves in series and no relief valve, so it is used for lower-hazard connections. An RPZ adds a relief valve between the check valves and protects against higher hazards. The assembly you need depends on the hazard classification and your water provider's rules.
A failed test means the assembly is not protecting the water supply and needs repair or replacement. After repairs, it must be tested again and the passing report submitted. Water providers can require action on failed or untested assemblies, so address a failed test promptly.
Often, yes. Leaks usually come from fouled check valves, worn seals or springs, or a faulty relief valve, and many can be fixed with replacement parts. If the assembly is corroded, freeze-damaged or obsolete, replacement may be the better option. The assembly must be retested after repair.
Denver Water requires testing by a certified backflow prevention assembly tester, with certification from ABPA or ASSE. A plumber's license is not the same as tester certification, so ask for the tester's certification number and confirm it before the test. Colorado law also governs who may inspect, test and repair devices.
Call (720) 390-2652 or use the contact form. Tell us your property type, the type and location of the device if you know it, and what is happening, such as a leak, a failed test or a notice from your water provider.
Contact Professional Plumbers Denver
To request backflow prevention service, tell us your property type, the type and location of your device if you know it, and what is happening, such as a leak, a failed test or a notice from your water provider.
Call (720) 390-2652 | Request Backflow Prevention Service | Ask About Backflow Installation
Professional Plumbers Denver, 4400 S Quebec St, Suite 208, Denver, CO 80237 | info@professional-plumbers-denver.com | Open 24 hours, 7 days a week



